MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 8 of 8
Search took
0.00
seconds.
Search:
Posts Made By:
cncnewb
Forum:
Introduce yourself and start planning
Thu 05 June 2014, 15:20
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
Thanks Brad and Pete. I had not come across the...
Thanks Brad and Pete. I had not come across the thread "Info on motor sizes link". The first line of the link accurately sums up the impression I was getting from reading threads on motor sizing. To...
Forum:
Introduce yourself and start planning
Thu 05 June 2014, 11:39
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
Brief aside: I am planning on completing the...
Brief aside: I am planning on completing the electronics portion first. One, because I am the least familiar with it, and two it seems to be advisable to set up the kitchen table test first so I...
Forum:
Introduce yourself and start planning
Thu 05 June 2014, 11:12
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
Ok, so after hours of more reading I think I have...
Ok, so after hours of more reading I think I have some ideas of what I need/want. Naturally I have a few questions so here we go.
1.) Motor selection:
I have decided that belt reduction is...
Forum:
Introduce yourself and start planning
Fri 23 May 2014, 20:53
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
Steve, Thanks for the reply. When you...
Steve,
Thanks for the reply. When you process a typical 4 x 8 panel for nested cabinets, what is your average routing time?
Also, I have been looking at cabinet software and all I can say...
Forum:
Introduce yourself and start planning
Tue 20 May 2014, 10:22
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
I received the same belt reduction feedback on...
I received the same belt reduction feedback on CNCZone so belt reduction it is.
After more reading on the MM forum I found a guy who seemed pleased with his MM and was running a 7 man cabinet shop...
Forum:
Introduce yourself and start planning
Mon 19 May 2014, 18:58
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
That's encouraging. I would be pretty pleased if...
That's encouraging. I would be pretty pleased if I could match that type of performance.
Forum:
Introduce yourself and start planning
Mon 19 May 2014, 16:12
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
Hi Darren, I was hoping you would reply,...
Hi Darren,
I was hoping you would reply, thank you. I have read your entire thread and you made several references to doing cabinet work with your MM. When you perform nested routing do you have...
Forum:
Introduce yourself and start planning
Mon 19 May 2014, 15:17
Replies:
15
Considering MM for sheets goods in GA
Views:
12,360
Posted By
cncnewb
Considering MM for sheets goods in GA
Hi all. I want to thank everyone here for their contributions, I have enjoyed reading them these past few days. This is more a less a x-post of a thread I made at CNCZone under a different handle, so...
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
14:14
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.