Forum: MechMates already cutting
Tue 02 September 2014, 17:48
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Tue 02 September 2014, 08:26
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Mon 01 September 2014, 17:25
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sat 21 December 2013, 21:19
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sun 28 April 2013, 09:41
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sat 30 March 2013, 17:06
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Wed 27 March 2013, 07:01
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Tue 26 March 2013, 17:33
|
Replies: 984
Views: 682,665
"warm" cup....Let me put it this way. I can...
"warm" cup....Let me put it this way. I can wrap both hands around the motor and keep them in place and not go "holy moly" that's hot! I am set roughly 3a/56VDC bipolar, I think it's a 22k...
|
Forum: MechMates already cutting
Tue 26 March 2013, 05:11
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sat 08 December 2012, 13:15
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Wed 28 November 2012, 11:22
|
Replies: 984
Views: 682,665
Interesting note about the backlash on the...
Interesting note about the backlash on the z-axis.
Maybe, just maybe a belt drive for the z-axis only might be in order. This would speed up the cutting process. I have experienced how much time...
|
Forum: MechMates already cutting
Thu 22 November 2012, 10:16
|
Replies: 984
Views: 682,665
The slight sheen I see in the photo could be a...
The slight sheen I see in the photo could be a couple of things.
The far right of object is the roughing area, the left of center is the finish pass area.
Are you sure the part isn't flexing up...
|
Forum: MechMates already cutting
Mon 12 November 2012, 03:07
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sun 11 November 2012, 05:24
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Thu 08 November 2012, 15:46
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Thu 08 November 2012, 06:53
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sun 21 October 2012, 09:03
|
Replies: 984
Views: 682,665
IF water flowing is your only real failure...
IF water flowing is your only real failure concern, then I would just focus on the simple solution so your machine won't start cutting unless water is flowing.
That could be a simple as a flow alert...
|
Forum: MechMates already cutting
Sun 21 October 2012, 06:20
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Sun 14 October 2012, 08:41
|
Replies: 984
Views: 682,665
Also check the following:
- pivot bolt for the...
Also check the following:
- pivot bolt for the motor plate, make sure it's not to tight, but allows movement
- spring pressure even on motor plate
- pinion's tight
- pinions fully seated in rack...
|
Forum: MechMates already cutting
Wed 20 June 2012, 13:52
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Wed 20 June 2012, 07:44
|
Replies: 984
Views: 682,665
|
Forum: MechMates already cutting
Mon 04 June 2012, 10:43
|
Replies: 984
Views: 682,665
Pete,
A few things to check:
- did you...
Pete,
A few things to check:
- did you lubricate the racks and pinion?
- Loose tension on the motors, is better than tight when binding happens
- double check for parallel alignment on the x1 and...
|
Forum: MechMates already cutting
Sat 02 June 2012, 08:25
|
Replies: 984
Views: 682,665
Pete,
I had the same problem with the Z axis...
Pete,
I had the same problem with the Z axis proximity on machine #28. The issue is that it touches the steel and is grounded on that machine. For some odd reason, the z axis proximity to the...
|
Forum: MechMates already cutting
Mon 28 May 2012, 17:45
|
Replies: 984
Views: 682,665
Pete,
That is a nice solution to the "toe in"...
Pete,
That is a nice solution to the "toe in" challenge that happens with some of the C channel available lately.
The "squaring" of the leg of that structural shape has been done a number of...
|
Forum: MechMates already cutting
Tue 03 April 2012, 19:57
|
Replies: 984
Views: 682,665
|