MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 7 of 7
Search took
0.00
seconds.
Search:
Posts Made By:
dbinokc
Forum:
MechMates already cutting
Sat 15 March 2014, 18:56
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
That is why I do not gamble. A one in four chance...
That is why I do not gamble. A one in four chance to get them both wrong and I did! :(
Forum:
MechMates already cutting
Sat 15 March 2014, 18:47
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
I think you got it. I did not mock mine up like...
I think you got it. I did not mock mine up like you did, so it was not until I mounted the gantry that I realized my error with the bracket.
Forum:
MechMates already cutting
Sat 15 March 2014, 18:29
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
Two things to watch out for that I did wrong on...
Two things to watch out for that I did wrong on my gantry. The smaller gantry end bracket with hole in it. Make sure you get it on the correct side. Also be sure which gantry rail gets the hole for...
Forum:
MechMates already cutting
Sun 09 February 2014, 21:53
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
If I do need to work the rails more on my...
If I do need to work the rails more on my machine, the plan is to get a good machinist straightedge and some bluing compound(dykem). I can use that to find the high spots on the rail and file them...
Forum:
MechMates already cutting
Sun 09 February 2014, 16:52
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
While I am not cutting yet, you are way closer...
While I am not cutting yet, you are way closer than me in precision. I decided to run with what I have and if I find that the rails are causing me problems with getting accurate cuts I will pull the...
Forum:
MechMates already cutting
Wed 05 February 2014, 06:55
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
The numbers look pretty good to me. A variation...
The numbers look pretty good to me. A variation of .13 mm and off at most .35mm from the 28mm target. Looking at my build, I think the worst that may happen if you are a little low is that the stop...
Forum:
MechMates already cutting
Tue 17 December 2013, 18:46
Replies:
735
Machining Aluminum #122 - Sydney, Australia
Views:
485,084
Posted By
dbinokc
Mike needs to move you into the Construction...
Mike needs to move you into the Construction Started heading. I think you are well out of the planning stage. :)
Showing results 1 to 7 of 7
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
14:39
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.