MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 11 of 11
Search took
0.00
seconds.
Search:
Posts Made By:
javeria
Forum:
MechMates already cutting
Tue 10 May 2011, 07:27
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
what is the blue pneumatic tube for - in the last...
what is the blue pneumatic tube for - in the last pic
Forum:
MechMates already cutting
Thu 16 December 2010, 02:02
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
good work Ken!
good work Ken!
Forum:
MechMates already cutting
Wed 07 April 2010, 14:06
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
OK I have a water bucket with a lid and a small...
OK I have a water bucket with a lid and a small hole for air to get in, then the pump outside - today I failed to notice that a foot and a half of teak wood saw dust was engulfing it and yet it was...
Forum:
MechMates already cutting
Tue 23 March 2010, 09:47
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
ken you can bench test the spindle without the...
ken you can bench test the spindle without the water pump connected
Forum:
MechMates already cutting
Mon 22 March 2010, 07:47
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
Helicoils are available - but a minimum qty...
Helicoils are available - but a minimum qty purchase and the need of another set of tap's and then the tool to insert the helicoil -
if its not so critical best would be to drill a hole and have a...
Forum:
MechMates already cutting
Fri 19 March 2010, 12:23
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
you are welcome ken! I use a grease gun with...
you are welcome ken!
I use a grease gun with normal auto bearing grease in it. also it would be interesting to see the rack mounted and the mounting of your motor, have you had enough place for...
Forum:
MechMates already cutting
Tue 09 March 2010, 05:45
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
Relax ken - been in similar situation a hundred...
Relax ken - been in similar situation a hundred times :)
Forum:
MechMates already cutting
Sun 07 March 2010, 08:05
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
Exactly
Exactly
Forum:
MechMates already cutting
Sun 07 March 2010, 07:33
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
ken try to slowly grind( I did that with my angle...
ken try to slowly grind( I did that with my angle grinder) the edges to get them to mate properly
Forum:
MechMates already cutting
Fri 22 January 2010, 13:11
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
hi Ken - what bob is that - the PP cable looks...
hi Ken - what bob is that - the PP cable looks thin - pls chk wire resistance between each pin, should be less that 0.3 ohm
Forum:
MechMates already cutting
Mon 16 November 2009, 07:51
Replies:
457
How to use Ubuntu - Klang Malaysia
Views:
238,737
Posted By
javeria
I vote for choice 3 - be careful with that Mobo-...
I vote for choice 3 - be careful with that Mobo- might blow again with all the wires inside, prefer to house it in its own cabinet.
mine went that way and there is no warranty for a burnt out one!
Showing results 1 to 11 of 11
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
03:44
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.