MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 8 of 8
Search took
0.00
seconds.
Search:
Posts Made By:
WilliamT
Forum:
Motors & their mountings
Thu 28 February 2019, 20:46
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
Correction Previous Post Earlier I labeled...
Correction Previous Post
Earlier I labeled my pinion as DP5. The pinion is DP20. Sorry for the confusion
Forum:
Motors & their mountings
Thu 28 February 2019, 06:20
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
Good question regarding ratios. Are we talking...
Good question regarding ratios. Are we talking here about gearbox ratios, or the overall drive ratio of the axis?
My MM is configured with DP5 rack, as most guys have done with their MM's and I am...
Forum:
Motors & their mountings
Tue 12 February 2019, 08:37
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
I would like to apologize for an error in my...
I would like to apologize for an error in my previous post!!
Earlier I said that the DMM Breakout boards is a true 5 axis controller. Sorry for the error earlier. The DMM board is a 4 axis...
Forum:
Motors & their mountings
Mon 04 February 2019, 15:07
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
Absolutely, this will work with the MechMate....
Absolutely, this will work with the MechMate. It's a true 5axis professional controller. You won't need Gecko's or SmoothStepper with this stuff.
And if you want to drive the Gantry with two...
Forum:
Motors & their mountings
Wed 18 July 2018, 09:50
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
Sure, I'll begin to put the information together....
Sure, I'll begin to put the information together. Perhaps it is best to start a fresh thread on the ClearPath servos with the Acorn controller. There we can discuss my setup, the good, the bad, and...
Forum:
Motors & their mountings
Fri 13 July 2018, 11:48
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
Brian, I used the same servo on all three...
Brian,
I used the same servo on all three axis, a Clearpath CPM-SDHP-3441D-ELN. You can find them here:
https://www.teknic.com/model-info/CPM-SDHP-3441D-ELN/?model_voltage=75VDC
It is very...
Forum:
Motors & their mountings
Thu 12 July 2018, 13:16
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
Alex - Thanks for the note. I'm using...
Alex - Thanks for the note.
I'm using CPM-SDSK-2310S-RLN. They are little NEMA23's and were the least expensive when purchased a few years ago.
After fighting control problems for more than two...
Forum:
Motors & their mountings
Thu 08 February 2018, 05:33
Replies:
24
Teknic Motor Question
Views:
49,234
Posted By
WilliamT
I use these servos and I like um...
Just noticed this thread. Sorry for the late reply.
I have these servos mounted to a MechMate and a Bridgeport in Austin. Send a pm if you are interested to see them run.
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
06:02
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.