MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Reload this Page Search Results
Register Options Profile Last 1 | 3 | 7 Days Today's Posts

Showing results 1 to 10 of 10
Search took 0.00 seconds. Search: Posts Made By: Rusty Nuts
Forum: Construction started, but not cutting yet Sat 01 November 2014, 08:43
Replies: 24
Views: 35,907
Posted By Rusty Nuts
I think it may delrin. I had a piece of round...

I think it may delrin. I had a piece of round stock that I made the bearing washers from. I used a removable locktite for the bolts so that they would not unscrew themselves while swinging the arm...
Forum: Construction started, but not cutting yet Fri 31 October 2014, 19:26
Replies: 24
Views: 35,907
Posted By Rusty Nuts
Hi Fox Here are photos of the slats...

Hi Fox

Here are photos of the slats installed. Turned out to be more work than I had planned. I couldn't bend the metal slats sharp enough by hand so I had to use a torch with a rose bud and heat...
Forum: Construction started, but not cutting yet Fri 31 October 2014, 19:19
Replies: 24
Views: 35,907
Posted By Rusty Nuts
1planeguy Here are some photos of my...

1planeguy

Here are some photos of my computer and monitor mount. Hope this will give you some ideas. The monitor box is mounted to a Lazy Susan so I can turn it to me when I'm on the side or end....
Forum: Construction started, but not cutting yet Thu 30 October 2014, 12:57
Replies: 24
Views: 35,907
Posted By Rusty Nuts
Ken I decided to go ahead and build the...

Ken

I decided to go ahead and build the table heavy since I don't want to have to build a second table later on. I probably won't cut much over a half inch thick but I want to be able to do more...
Forum: Construction started, but not cutting yet Tue 28 October 2014, 19:40
Replies: 24
Views: 35,907
Posted By Rusty Nuts
Hi Mike I just have my wife go out everyday...

Hi Mike

I just have my wife go out everyday before I get home from work and vacuum and mop the shop. If you believe that, then I have some land I will sell you cheap, lot 1009458 on the far side...
Forum: Construction started, but not cutting yet Wed 22 October 2014, 20:10
Replies: 24
Views: 35,907
Posted By Rusty Nuts
Thanks Alan. 1planeguy, I will take some...

Thanks Alan.

1planeguy, I will take some close ups tomorrow.

Gary
Forum: Construction started, but not cutting yet Tue 21 October 2014, 19:00
Replies: 24
Views: 35,907
Posted By Rusty Nuts
Here are some updated photos of the Mechmate...

Here are some updated photos of the Mechmate router. I have added a vacuum system and mounted the computer in a box with the monitor in a cabinet. There is a fan and filter in the box which keeps...
Forum: Construction started, but not cutting yet Tue 21 October 2014, 18:42
Replies: 24
Views: 35,907
Posted By Rusty Nuts
These photos are of a roller that I am...

These photos are of a roller that I am fabricating. It will be mounted on the front end of the table to help with loading the steel sheets onto the bed. My wife has informed me that she is not going...
Forum: Construction started, but not cutting yet Tue 21 October 2014, 18:29
Replies: 24
Views: 35,907
Posted By Rusty Nuts
Finally got time to take a few more photos....

Finally got time to take a few more photos. Gantry and Y Car built, rails ground and beveled, and cable tray rails built and installed. I should be able to get the water table bent this Friday and...
Forum: Construction started, but not cutting yet Mon 06 October 2014, 19:08
Replies: 24
Views: 35,907
Posted By Rusty Nuts
CNC Plasma Table build - Valley Grande, Alabama

Hi Mike

Here is the start of my plasma table build. Thanks for the fast shipment of the laser cut parts. This will have a water table in the bed and will probably have a storage tank underneath to...
Showing results 1 to 10 of 10

 
Forum Jump

All times are GMT -6. The time now is 15:28.

Contact Us - www.mechmate.com - Archive - Top

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.