Forum: Construction started, but not cutting yet
Mon 11 December 2017, 12:48
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Thu 07 December 2017, 04:57
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Wed 06 December 2017, 16:11
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 02 December 2017, 11:49
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 02 December 2017, 11:41
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 19 November 2017, 19:30
|
Replies: 232
Views: 227,725
If you swapped the motor to your X or B axes...
If you swapped the motor to your X or B axes (assuming they are the same motors) and they move that axis fine I would lean toward a weight issue. If you can't swap it with one of those then use the...
|
Forum: Construction started, but not cutting yet
Sun 19 November 2017, 19:29
|
Replies: 232
Views: 227,725
I use a 880 oz-in motor for my z. I use a ball...
I use a 880 oz-in motor for my z. I use a ball screw for mine and it is overkill but I already had it. Still even with that I have a extension spring to equalize the weight of the Z so it will not...
|
Forum: Construction started, but not cutting yet
Sun 19 November 2017, 19:22
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Tue 31 October 2017, 14:21
|
Replies: 232
Views: 227,725
From the video it appears you can move in one...
From the video it appears you can move in one direction and not the other. Is that correct?
I have heard whining and grinding before at work when either the motion in the one direction has...
|
Forum: Construction started, but not cutting yet
Mon 30 October 2017, 19:46
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 07 October 2017, 07:59
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 15 November 2015, 10:11
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 14 November 2015, 11:46
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 29 August 2015, 23:15
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 23 August 2015, 21:57
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 20 June 2015, 19:32
|
Replies: 232
Views: 227,725
If you follow the prints for the length of your...
If you follow the prints for the length of your longitudinal beams,then it will be for that distance of cutting. I would add a couple of inches for wiggle room in my honest opinion. When looking at...
|
Forum: Construction started, but not cutting yet
Sat 20 June 2015, 18:56
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sat 20 June 2015, 17:51
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Wed 10 June 2015, 21:15
|
Replies: 232
Views: 227,725
I hate to give such a vague answer but near the...
I hate to give such a vague answer but near the end of the 126 manual it gives the cross reference from parallel to the port 1 and port 2 pins. This is where it can be confusing but you have to go...
|
Forum: Construction started, but not cutting yet
Wed 10 June 2015, 20:28
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Tue 02 June 2015, 09:37
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 31 May 2015, 22:17
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 31 May 2015, 20:38
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 31 May 2015, 20:33
|
Replies: 232
Views: 227,725
|
Forum: Construction started, but not cutting yet
Sun 31 May 2015, 20:07
|
Replies: 232
Views: 227,725
|