Forum: MechMates already cutting
Tue 19 November 2019, 18:33
|
Replies: 216
Views: 214,815
Are your steppers reading ok with a meter? You...
Are your steppers reading ok with a meter? You definitely have a problem with the B set of windings on two different drives. This leads me to believe that two drives are bad which is unlikely at the...
|
Forum: MechMates already cutting
Tue 19 November 2019, 18:26
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sun 25 October 2015, 11:35
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Mon 10 February 2014, 17:32
|
Replies: 216
Views: 214,815
Going back and reading post #1...
Going back and reading post #1 (http://www.mechmate.com/forums/showthread.php?p=64253&postcount=1), I wonder, does she still think you were crazy for making this machine?
|
Forum: MechMates already cutting
Sat 08 February 2014, 16:16
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sat 08 February 2014, 16:11
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Tue 04 February 2014, 04:38
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Tue 04 February 2014, 04:36
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Mon 03 February 2014, 04:36
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sat 01 February 2014, 12:19
|
Replies: 216
Views: 214,815
The Hitachi WJ200 I have has a safety circuit...
The Hitachi WJ200 I have has a safety circuit built into it that I use to disable the spindle while doing a tool change with an emergency stop button that is linked only to it. It will not run if a...
|
Forum: MechMates already cutting
Wed 29 January 2014, 13:58
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sat 18 January 2014, 14:01
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sat 11 January 2014, 11:02
|
Replies: 216
Views: 214,815
The top of the teeth should not pose a problem,...
The top of the teeth should not pose a problem, just remove the sharp burrs. The pressure angle is where the contact is made. Just do not forget to use a good grease to help prevent wear. I do not...
|
Forum: MechMates already cutting
Fri 10 January 2014, 20:30
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Wed 08 January 2014, 14:32
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Thu 26 December 2013, 17:45
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Mon 23 December 2013, 21:28
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sun 08 December 2013, 13:30
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sun 08 December 2013, 08:31
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Fri 15 November 2013, 20:52
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Fri 15 November 2013, 20:49
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Thu 14 November 2013, 04:33
|
Replies: 216
Views: 214,815
|
Forum: MechMates already cutting
Sun 10 November 2013, 10:40
|
Replies: 216
Views: 214,815
Mich,
Just catching up on your thread. Nice...
Mich,
Just catching up on your thread. Nice to have another person who likes the challenge. Building the machine is not that hard. Just takes time and for some of us longer than others. You...
|