Forum: MechMates already cutting
Thu 17 September 2015, 09:32
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Tue 02 June 2015, 11:20
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Tue 02 June 2015, 06:35
|
Replies: 1,078
Views: 1,397,594
And here...
And here http://www.onsrud.com/xdoc/composite-cutting-tools
|
Forum: MechMates already cutting
Tue 02 June 2015, 06:28
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 06 September 2014, 15:54
|
Replies: 1,078
Views: 1,397,594
Water will not but glycol may. Food Service PU...
Water will not but glycol may. Food Service PU will be more resistant. But I was not saying not to use it. I use PU on mine, however, caution should be taken when using anything without evaluating...
|
Forum: MechMates already cutting
Sat 06 September 2014, 15:26
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 06 September 2014, 12:39
|
Replies: 1,078
Views: 1,397,594
Fox,
PU tubing will degrade, swell and...
Fox,
PU tubing will degrade, swell and rupture with various chemicals. Even oil in air lines has its toll on it. In this pdf is a guideline list on what PU is affected by. ...
|
Forum: MechMates already cutting
Thu 14 August 2014, 20:40
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sun 08 June 2014, 10:15
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 07 December 2013, 04:41
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 07 December 2013, 04:41
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 07 December 2013, 03:43
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 30 November 2013, 07:29
|
Replies: 1,078
Views: 1,397,594
Ross,
Again thanks for sharing.
In reply...
Ross,
Again thanks for sharing.
In reply to post #967 (http://www.mechmate.com/forums/showthread.php?p=64697&postcount=967)
"Fun trick: clamp a "heavy/sturdy" steel rod or beam you think is...
|
Forum: MechMates already cutting
Thu 21 November 2013, 04:37
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Sat 16 November 2013, 14:06
|
Replies: 1,078
Views: 1,397,594
Fernando and Al,
I work industrial...
Fernando and Al,
I work industrial maintenance (electo-mechanical technician). I will tell you that any machine likes to be clean. A clean machine will treat you well for years. Just like a...
|
Forum: MechMates already cutting
Tue 05 November 2013, 04:22
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Tue 13 August 2013, 14:22
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Mon 12 August 2013, 09:31
|
Replies: 1,078
Views: 1,397,594
Ross,
Is there any particular reason you used...
Ross,
Is there any particular reason you used an extended head prox? It does not look as if you were worried about an increased sensing distance or side sensing. An embedded model would tighten up...
|
Forum: MechMates already cutting
Tue 11 June 2013, 15:33
|
Replies: 1,078
Views: 1,397,594
|
Forum: MechMates already cutting
Wed 06 March 2013, 19:22
|
Replies: 1,078
Views: 1,397,594
|