MechMate CNC Router Forum - Search Results

		MechMate CNC Router Forum > Search Forums
Search Results

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Showing results 1 to 9 of 9
Search took 0.00 seconds. Search: Posts Made By: Aubrey

Forum: 80. Computer Hardware & Software

Sat 21 July 2007, 15:09

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

If I understand you correctly, the 4.7k may be...

If I understand you correctly, the 4.7k may be too much resistance and a direct connection may be too little.

This may be a dumb thought but how about a 4.7k trimpot? That way one could "fine...

Forum: 80. Computer Hardware & Software

Sat 21 July 2007, 14:53

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Stage 2 Done

Hi Guys
Thanks to Mike the charge pump circuit he donated has been inserted into the controler (and corrections made to the opto-isolator connections on the auxiliary switches):o
The image of the...

Forum: 80. Computer Hardware & Software

Sat 21 July 2007, 06:02

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Belated Post

Hi People
Net Connection problem took a week to resolve - just "came right":confused:
Mike:
Thanks for your patience.... appreciated!
I've been building up an image of the circuit and although...

Forum: 80. Computer Hardware & Software

Sun 15 July 2007, 07:08

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Are they both set up on the same ADSL router?

Are they both set up on the same ADSL router?

Forum: 80. Computer Hardware & Software

Sat 14 July 2007, 15:56

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Megapost

Hi guys

NOTE ABOUT THIS POST:
Due to some bottleneck in the internet, the lines out of South Africa are VERY slow. So slow that the MechMate site times out when I try to post to the forum but I...

Forum: 80. Computer Hardware & Software

Thu 12 July 2007, 16:05

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

General Note/appology/explanation

I've just read this whole thread again and if I was someone else, I would think that I was an idiot. I'm griping about prices all the way.
I'm just recovering from a year and a half of unemployment....

Forum: 80. Computer Hardware & Software

Thu 12 July 2007, 14:19

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Thanks Gerald I did have a quick look at the...

Thanks Gerald
I did have a quick look at the plans while they were printing last night and now that you mention it, I remember the dual motor setup --- Sorry!
I intend doing a bit more studying...

Forum: 80. Computer Hardware & Software

Thu 12 July 2007, 12:39

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Thanks for feedback

Gentlemen!
Thanks for the quick responses.
If nothing else, my post proves my point about being a below average novice as far as electronics is concerned.:(
Tom.
It seems the G100 is the...

Forum: 80. Computer Hardware & Software

Wed 11 July 2007, 14:30

Replies: 31

Lower Cost Electronics?

Views: 50,875

Posted By Aubrey

Lower Cost Electronics?

Hi Guys,
Congratulations on a lively forum!
Working in a CNC shop, my problem is not the mechanicals but the electronics:(
Gerald suggests the PMDX-122 breakout board and the Geko G-Rex G100...

Showing results 1 to 9 of 9

Forum Jump

All times are GMT -6. The time now is 22:03.