Forum: MechMates already cutting
Sat 01 August 2009, 19:12
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Sat 01 August 2009, 15:55
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Tue 09 June 2009, 07:28
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Mon 04 May 2009, 18:14
|
Replies: 489
Views: 404,099
John,
There are many around. Most home...
John,
There are many around. Most home centers sell it as a sealer / anti-friction agent for table saw tops. Topcoate, Boeshield are ones some guys are using, probably many other names as...
|
Forum: MechMates already cutting
Fri 01 May 2009, 10:42
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Wed 29 April 2009, 14:59
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Fri 30 January 2009, 11:28
|
Replies: 489
Views: 404,099
Sean,
Maybe you could up a pic or two...
Sean,
Maybe you could up a pic or two of the indexer stuff you are machining? :) I am sure there is a lot of interest in seeing some MM indexer work.
I have visited the Amish in PA when...
|
Forum: MechMates already cutting
Fri 30 January 2009, 07:32
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Tue 25 November 2008, 21:25
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Thu 18 September 2008, 18:04
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Fri 15 August 2008, 11:46
|
Replies: 489
Views: 404,099
Sean,
I remember a while back you said...
Sean,
I remember a while back you said you were thinking about switching from the 20 tooth to 30 or 35 tooth pinions to get a little more speed. Did this help anything and did your cut...
|
Forum: MechMates already cutting
Wed 14 May 2008, 11:04
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Thu 01 May 2008, 21:45
|
Replies: 489
Views: 404,099
Doug,
Would it be that hard to change...
Doug,
Would it be that hard to change the pinions around and see which one gives you the type of performance you want? Sorta like tuning the gearing on a car. Or is it a lot more work...
|
Forum: MechMates already cutting
Fri 18 April 2008, 21:06
|
Replies: 489
Views: 404,099
Gerald,
Didnt you mention at one...
Gerald,
Didnt you mention at one time you were going to try the geared motors on one of your machines? That still in the works? Or am I remembering it wrong?
|
Forum: MechMates already cutting
Thu 17 April 2008, 20:27
|
Replies: 489
Views: 404,099
Sean,
What do you use to do your flame...
Sean,
What do you use to do your flame polishing? Does that just gloss over the cut edge? Haven't done too much with acrylics myself. Where on earth did you pick up all these skills?
|
Forum: MechMates already cutting
Thu 17 April 2008, 19:08
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Thu 28 February 2008, 06:34
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Mon 25 February 2008, 06:37
|
Replies: 489
Views: 404,099
Sean,
I have seen a lot of posts with...
Sean,
I have seen a lot of posts with you mentioning how hard your new beast is working. How about a few pictures of some of your cuts if you get a chance. :)
Heath.
|
Forum: MechMates already cutting
Tue 19 February 2008, 07:12
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Fri 15 February 2008, 08:13
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Wed 06 February 2008, 08:33
|
Replies: 489
Views: 404,099
|
Forum: MechMates already cutting
Wed 06 February 2008, 08:13
|
Replies: 489
Views: 404,099
Gerald, Sean,
Thanks for the...
Gerald, Sean,
Thanks for the reply. I might try the cold rolled as then I could use the skate as well. I could always change to a machined tool steel slide later.
Sean,
...
|
Forum: MechMates already cutting
Tue 05 February 2008, 10:32
|
Replies: 489
Views: 404,099
Sean,
Is A36 cold rolled flat the same...
Sean,
Is A36 cold rolled flat the same as tool steel? Is that what I should ask for, or is that a sub you did? If it is a sub, is there any downside like wearing and such? You can tell...
|
Forum: MechMates already cutting
Tue 05 February 2008, 07:22
|
Replies: 489
Views: 404,099
Sean,
Is Tool Steel harder than angle...
Sean,
Is Tool Steel harder than angle or tubing? Was it more difficult to grind than the rails with the skate grinder? I have seen a lot of posts from people saying they had the z slide...
|
Forum: MechMates already cutting
Fri 18 January 2008, 07:26
|
Replies: 489
Views: 404,099
|