MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Reload this Page Search Results
Register Options Profile Last 1 | 3 | 7 Days Today's Posts

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: Marc Shlaes
Forum: MechMates already cutting Fri 30 May 2008, 21:39
Replies: 489
Views: 407,488
Posted By Marc Shlaes
There is a thread on Speeds, Feeds, Bits and...

There is a thread on Speeds, Feeds, Bits and Materials (http://www.mechmate.com/forums/showthread.php?t=724&highlight=speeds). Move the discussion there (done) and keep going. This helps us beginners...
Forum: MechMates already cutting Thu 01 May 2008, 18:23
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Ok, I have an Oxy/ Actl setup. Do you get a...

Ok, I have an Oxy/ Actl setup. Do you get a hydrogen bottle at any welding supply? Never asked for that.

Next question...

With 7.2 gearboxes, what pinion and what is your max ipm jog speed?
...
Forum: MechMates already cutting Thu 01 May 2008, 16:37
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Sean, Could you post an example of a...

Sean,

Could you post an example of a "hydrogen fired torch"?

Also, I can't remember... Do you have the 3.6 gearboxes or the 7.2?

Thx.
Forum: MechMates already cutting Fri 07 March 2008, 06:19
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Sean, Can you give me the trade name for...

Sean,

Can you give me the trade name for that laminate covered birch core ply? I would like to see if I can get that locally here in Cleveland.

Thx!
Forum: MechMates already cutting Wed 27 February 2008, 10:28
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Hey, I like the rough shape of that foot! :) ...

Hey, I like the rough shape of that foot! :) Sean, go check out the 4th evolution on JR's pages.
Forum: MechMates already cutting Mon 18 February 2008, 09:30
Replies: 489
Views: 407,488
Posted By Marc Shlaes
We cut usually in 2-3 passes. We were just...

We cut usually in 2-3 passes. We were just learning and wanted to minimize side forces using minimal clamps.

We cut some 1/2in. CPVC (the solid not the expanded stuff) pretty much in one pass...
Forum: MechMates already cutting Sun 17 February 2008, 22:24
Replies: 489
Views: 407,488
Posted By Marc Shlaes
J.R. and I were routinely cutting mdf at 120ipm...

J.R. and I were routinely cutting mdf at 120ipm with a 1/4in downcut spiral (solid carbide). We got a pretty good cut at 240 also.
Forum: MechMates already cutting Fri 18 January 2008, 11:49
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Sean, Is this your first? WOW! My advice......

Sean,

Is this your first? WOW! My advice... Start teaching them early on that mirrors are often used for more that putting on make-up and doing your hair. My second (and last) just learned to...
Forum: MechMates already cutting Fri 04 January 2008, 16:00
Replies: 489
Views: 407,488
Posted By Marc Shlaes
I plan on only using the skate to grind the...

I plan on only using the skate to grind the angle. I bought a SteelMax saw. It cuts through 1/4" steel like butter. Amazing. Steel isn't the slightest bit warm after the cut.
Forum: MechMates already cutting Sat 03 November 2007, 07:48
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Sean, Are you planning to make it out of...

Sean,

Are you planning to make it out of melamine for the sake of airtightness or MDF and simply paint it. Also, if you are going to silicone it to the spoil board, I assume that you are never...
Forum: MechMates already cutting Fri 02 November 2007, 14:49
Replies: 489
Views: 407,488
Posted By Marc Shlaes
Sean, Did you drill both at the same time...

Sean,

Did you drill both at the same time so that you only had one setup?

Can you elaborate on your vacuum design / thoughts?

I use vacuum clamping and gluing a lot and I am very...
Showing results 1 to 11 of 11

 
Forum Jump

All times are GMT -6. The time now is 09:35.

Contact Us - www.mechmate.com - Archive - Top

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.