Forum: MechMates already cutting
Tue 23 May 2017, 21:42
|
Replies: 48
Views: 60,488
Thanks for the help and suggestions.
I have...
Thanks for the help and suggestions.
I have adjusted the shim washers to improve the "at rest" squareness. I will evaluate the success of the adjustment over the next week.
I have the...
|
Forum: MechMates already cutting
Mon 22 May 2017, 14:56
|
Replies: 48
Views: 60,488
|
Forum: MechMates already cutting
Sun 21 May 2017, 19:22
|
Replies: 48
Views: 60,488
|
Forum: MechMates already cutting
Mon 29 July 2013, 17:59
|
Replies: 48
Views: 60,488
|
Forum: MechMates already cutting
Mon 29 July 2013, 05:52
|
Replies: 48
Views: 60,488
Dust foot completed
I have completed the dust foot and it is performing very well. I have a small portable dust collector attached to it and very little dust escapes the brushes or is left on the table.
I used it to...
|
Forum: MechMates already cutting
Tue 18 June 2013, 04:24
|
Replies: 48
Views: 60,488
I know that Dimitry has done something very...
I know that Dimitry has done something very similar to what I plan to do and is apparently having success.
http://www.mechmate.com/forums/showthread.php?t=2135&highlight=dust+foot&page=5
|
Forum: MechMates already cutting
Mon 17 June 2013, 15:25
|
Replies: 48
Views: 60,488
Some advise needed:
I have purchased two ARO...
Some advise needed:
I have purchased two ARO self feed drills to install next to the spindle. If I install a second z slide for this purpose, I will have to move the existing spider away from 0,0...
|
Forum: MechMates already cutting
Mon 06 May 2013, 05:29
|
Replies: 48
Views: 60,488
Thanks Nils.
The inside is wood. This unit...
Thanks Nils.
The inside is wood. This unit is made from Birch which seems to be the species of choice for most homeowners in this area.
There is a stainless steel exhaust unit that sits inside...
|
Forum: MechMates already cutting
Sun 05 May 2013, 18:30
|
Replies: 48
Views: 60,488
First Project Completed
Mechmate #106 and its first completed projected. The range hood will be installed tomorrow.
|
Forum: MechMates already cutting
Thu 25 April 2013, 19:59
|
Replies: 48
Views: 60,488
|
Forum: MechMates already cutting
Thu 25 April 2013, 05:26
|
Replies: 48
Views: 60,488
Thanks Mike,
#106 - Will have to get that...
Thanks Mike,
#106 - Will have to get that serial number on vinyl and place it on my machine.
As you can see from the photo, the cables to the z-slide are being supported by a wooden dowel. I...
|
Forum: MechMates already cutting
Wed 24 April 2013, 21:03
|
Replies: 48
Views: 60,488
Thanks everyone.
@Heath: Its nice to hear...
Thanks everyone.
@Heath: Its nice to hear from you at this point in my build. If you can recall, my build started quite awhile ago with a few shipments that arrived with your help. It was much...
|
Forum: MechMates already cutting
Wed 24 April 2013, 19:30
|
Replies: 48
Views: 60,488
|
Forum: MechMates already cutting
Wed 24 April 2013, 19:27
|
Replies: 48
Views: 60,488
Mechmate for Newfoundland comes to life!!!!
Hi all.
I could wait no longer. My machine is alive and cutting. There are a few details that need some tidying up but a paying job required that I get things done in a hurry.
Here she is ....
|
Forum: MechMates already cutting
Thu 12 May 2011, 16:35
|
Replies: 48
Views: 60,488
Fear Not The Grinding Of the Rails
I thought it would be best to begin my build with the item that was giving me great concern. I knew that purchasing v rails was an option (allbeit expensive) but I also wanted the experience of...
|
Forum: MechMates already cutting
Mon 04 April 2011, 18:37
|
Replies: 48
Views: 60,488
Hi Ros,
Yes, Buibui's table has been a great...
Hi Ros,
Yes, Buibui's table has been a great influence. I have left an opening in the front approx. 50" so I can store sheet goods underneath. I am in the process of adding gussett plates to...
|
Forum: MechMates already cutting
Mon 04 April 2011, 15:10
|
Replies: 48
Views: 60,488
Drawings
Hi everyone,
My build has started. I have already completed much of the base table and will post pictures as soon as I can. In the meantime, I have attached three CAD drawings of my machine. ...
|
Forum: MechMates already cutting
Fri 28 May 2010, 17:53
|
Replies: 48
Views: 60,488
Hi Tony,
I have seen transfer rollers used...
Hi Tony,
I have seen transfer rollers used to reduce friction when moving the grinder back and forth to cut down the angle to the correct height. However, I have not seen them used to grind the...
|
Forum: MechMates already cutting
Fri 28 May 2010, 17:43
|
Replies: 48
Views: 60,488
Skate roller
I am been giving some thought to the upcoming rail grinding. To avoid the grooves that gets worn into the bolts and the possibly into the referencing surface on the rails, I have seen some builders...
|
Forum: MechMates already cutting
Tue 27 April 2010, 10:37
|
Replies: 48
Views: 60,488
Neutrik connectors and shielding
I am considering using Neutrik connectors at the control box and motors. I have seen it done by several members here and the outcome looks very professional.
I have a question regarding...
|
Forum: MechMates already cutting
Wed 07 April 2010, 08:16
|
Replies: 48
Views: 60,488
Hi Robert.
I have put together an order to...
Hi Robert.
I have put together an order to Igus (through the same rep for you area) and also to Factorymation. I have not completed the order because I am still researching.
Another request I...
|
Forum: MechMates already cutting
Wed 07 April 2010, 04:26
|
Replies: 48
Views: 60,488
Thanks Heath.
The bent parts you provided...
Thanks Heath.
The bent parts you provided are of excellent quality. I will say hi to Glenda for you when I see her.
Thanks Mike,
I am enjoying everthing this forum has to offer.
Clayton
|
Forum: MechMates already cutting
Tue 06 April 2010, 18:03
|
Replies: 48
Views: 60,488
First Project Completed! #106 - NL Canada
Hi to all Mechmate forum members.
My name is Clayton and I live in Bishop's Falls, Newfoundland, Canada. I have been a "silent" member of the "Mechmate family" since November and from the first...
|