Forum: MechMates already cutting
Sun 18 May 2014, 22:21
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Fri 16 May 2014, 23:36
|
Replies: 518
Views: 322,693
I do not suspect the cable & motor, the issue...
I do not suspect the cable & motor, the issue looks like its lies somewhere from the driver up to the PC.
For good measure, Register-Cleaner your Win XP. check the parallel port before you pull...
|
Forum: MechMates already cutting
Fri 16 May 2014, 05:26
|
Replies: 518
Views: 322,693
You found 2 things, your motor AND cable is...
You found 2 things, your motor AND cable is fine.!!
now its pointing at your driver & up stream, maybe the BOB, LPT cable & LPT port.
No experience with Gecko 203... I use economical drivers.
...
|
Forum: MechMates already cutting
Thu 15 May 2014, 23:40
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Wed 14 May 2014, 23:00
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Thu 30 May 2013, 01:49
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Mon 28 May 2012, 05:21
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Wed 02 May 2012, 05:17
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Fri 23 December 2011, 22:11
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Fri 23 December 2011, 01:49
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Sun 19 June 2011, 21:11
|
Replies: 518
Views: 322,693
I squared up the spindle (as per Gerald's...
I squared up the spindle (as per Gerald's instructions) when I set up the Z-axis & forget about it after that. I'll take your advise & carry out routine periodic checks in the future.
One of the...
|
Forum: MechMates already cutting
Sun 19 June 2011, 00:11
|
Replies: 518
Views: 322,693
Russel, Thanks. Some how, I can never get this...
Russel, Thanks. Some how, I can never get this type of speed with this type of depth. I can only safely run at most 2800mm/min (110ipm)at 6mm steps (1/4")... if the material is over 12mm, I'll have...
|
Forum: MechMates already cutting
Fri 17 June 2011, 22:45
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Wed 01 June 2011, 10:19
|
Replies: 518
Views: 322,693
Russel,
you can do without the SSR & use a...
Russel,
you can do without the SSR & use a magnetic coil contactor for the dust collector, & wire a remote push button to active the contactor. Easy, economical, reliable & conventional.
|
Forum: MechMates already cutting
Thu 02 December 2010, 05:25
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Sat 27 November 2010, 21:13
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Tue 26 October 2010, 08:40
|
Replies: 518
Views: 322,693
It is necessary here... ambient temp daytime...
It is necessary here... ambient temp daytime 30~35 C, 28~30C night...
BUT evaporative cooler doesn't work well here, our wet temp is 25~26C so can nly get 26~28C from the cooler... I'll be better...
|
Forum: MechMates already cutting
Tue 26 October 2010, 04:54
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Tue 26 October 2010, 03:57
|
Replies: 518
Views: 322,693
Russel, you can fix the penal under the table....
Russel, you can fix the penal under the table. That is exactly how I did it. from here, I can just push the whole rig anywhere on the fly. There are lots of room under the spoil board... Am seriously...
|
Forum: MechMates already cutting
Sat 23 October 2010, 01:54
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Thu 15 July 2010, 22:29
|
Replies: 518
Views: 322,693
Good to know you are back on your feet.
You...
Good to know you are back on your feet.
You made a good choice to build the table up-side down, a lot safer & less back-breaking. Just make sure you have enough hands & pay extra safety precautions...
|
Forum: MechMates already cutting
Wed 23 June 2010, 09:56
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Fri 11 June 2010, 07:12
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Sat 17 April 2010, 21:57
|
Replies: 518
Views: 322,693
|
Forum: MechMates already cutting
Mon 22 March 2010, 22:17
|
Replies: 518
Views: 322,693
|