Machine now cutting!....Seahorses! - Skopje,Macedonia
 

First greetings to all,
otherwise I'm from Macedonia and I want to publicly praise Danilo # 64 and say that he is the man who encouraged me to try to make MM.
Thank you Danilo.
Building on my machine are likely longer than what we're used to seeing here on the forum because of my engagement in the workplace.However I will try not to last forever and normal to share the experience with you.Just to mention that I have sufficient knowledge in this area and hopefully help and suggestions from you guys.
P.S.If I'm wrong somewhere in writing this is because I never studied English.:rolleyes::rolleyes:
See you soon hopefully.

Welcome!
Take your time to build. With Danilo in your neighbourhood, you can't go wrong :)

Thank you Ken.
Here are the first purchased parts needed for my adventure(at this point I'm scared to tell you for my MM so I will call this my adventure because I do not have enough knowledge in this area ):o
I know that house is not built from the roof but I had to start somewhere and even from the roof.:)
I bought two pieces ABB VFD because planning to put two Z axes in the Y trolley.

http://www.facebook.com/media/set/?s...type=3&theater

http://www.facebook.com/media/set/?s...type=3&theater

http://www.facebook.com/media/set/?s...type=3&theater

These days I plan to purchase by DEITECH two spindles DTS-23 2,2KW.
Ask for opinion?:confused:

I learned how to attach photos:)
I think this is better.
Attachment 12537

Attachment 12538

Attachment 12539

Go for 3KW if your budget allows.

Ken,do you think that 2.2kw not enough for processing of aluminum composite panels with 4mm thick?

Should be fine.....2.2Kw should do that easily. My 1.5HP router does.

For Aluminium composite, that should be enough.

My Waterjet Cut and Bent Parts finally arrived.Will post the pics very soon.
Currently I have a dilemma and seek advice.
Ordering engines DEITECH series model 86HS9802 (http://www.driver-motor.com/ProductContent.aspx?ID=47) 2.4mH and ask for advice on which driver to decide DM556 or DM856 (http://www.driver -motor.com/ProductList.aspx? CID = 5).
Will anyone help guys about this?

Problems starting now,
see just how awry.
one he rolled it certain that he was drunk or first time doing this.

Here are all parts and all that are bent must to intervene or to correct them.:mad:

Here's what happens these days:)

more:)

& more;)

finally arrived and shipping from DEITECH CHINA

back problems, 200/75mm DIN standard deformed to maximum and I forced myself to dig up the snow and find some better.
(that's our kind sellers):mad::mad::mad:

welding base table,
And who would have turned upside down now this monster,:D

Great progress pics !! Keep up the great work !!

Thanks Mike.

Bushings and V Bearings made and strengthened (tempered).

No loctite.

Nicely done !!

Snow has less candle so we decided to get out to paint.I decided tell to you more through the pictures then through talking (due to my poor knowledge of English language):o

Work are flowing

If you are wondering why I do not have any photos of my V rails it is because the subject has eaten my nerves.
In the end I was happy with 0.3mm tolerance.

Нека каже некој ве молам дека е 0.3мм како што треба.
Ќе ми значи многу.:)

Opsss-translate
Let somebody please tell that the 0.3mm tolerance for V rails is OK.
I'll mean a lot

If your saying you have a .3mm tolerance in height (.0118") then shim with soda can strips. If between rails loosen bolts and adjust with a mallet.

Pajka
The link below describes a straightforward way to align your rail height and straightness.

http://www.mechmate.com/forums/showthread.php?t=3440

Thanks guys.