701. Motor Drives - Page 2 - MechMate CNC Router Forum

		MechMate CNC Router Forum > Electrical & Electronic
701. Motor Drives

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 2 of 2

Threads in Forum : 701. Motor Drives

Forum Tools

Search this Forum

Thread / Thread Starter	Last Post	Replies	Views
Differences between G201, G202 and G203 stepper drives from Geckodrive ( 1 2) Gerald_D	Tue 03 April 2012 11:06 by darren salyer	59	78,461
Geckodrives (California USA) ( 1 2 3 ... Last Page) Gerald_D	Fri 09 July 2010 12:20 by renraku	148	165,956
Using the Gecko G540 drive a MechMate ( 1 2) stefanv	Sat 07 May 2011 03:45 by MAC2009	42	68,645

Read from Multiple Coils lukebarber	Thu 02 March 2017 12:04 by danilom	1	9,031
Spindle Frequency? lukebarber	Sat 23 March 2019 18:36 by lonestaral	2	25,116
Buck Boost Transformer 380V 240V 3phase lukebarber	Fri 24 August 2018 19:15 by MetalHead	1	7,174
One system controlling two tables? Mountaincraft	Fri 10 September 2010 18:27 by smreish	4	17,363
Gecko 203v intermittent fault paul60	Fri 12 September 2014 16:54 by smreish	17	26,284
Suspect gecko G 203V problem paul60	Thu 03 October 2013 09:19 by Richards	5	11,472
axis X one stepper motor renraku	Sat 12 June 2010 12:59 by smreish	17	20,606
how to assign gecko driver to motors? renraku	Sun 12 September 2010 15:48 by Red_boards	3	9,566
Ruminations on production and stepper motors Richards	Tue 23 October 2012 06:31 by bradm	8	12,090
How to calculate resistor needed for gecko drives Richards	Wed 15 May 2013 08:52 by smreish	8	14,568
Use Arduino Uno to test stepper drivers and stepper motors Richards	Sat 13 December 2014 11:12 by Richards	0	7,608
How much voltage do I really need? Richards	Thu 18 July 2013 17:54 by Richards	29	32,945
Geckodrive announced the GM215 stepper motor drive Richards	Sun 18 January 2015 10:21 by Robert M	1	7,783
Would a size 23 motor work? Richards	Thu 08 November 2012 09:12 by Richards	3	10,263
Electrical Phase Type Compatible rocky2889	Sat 07 March 2009 22:29 by rocky2889	0	5,986
Spindle Collet rocky2889	Sat 28 February 2009 14:45 by rocky2889	3	6,101
Selecting resistors for Gecko drive Rusty Nuts	Mon 29 August 2011 19:49 by smreish	9	12,174
Gecko / Motor Tuning sailfl	Tue 06 April 2010 12:13 by Kobus_Joubert	9	13,318
Max power supply voltage for Gecko G540 shaper	Tue 11 August 2009 10:38 by Gerald D	6	9,656
Found a new type of driver could save some money please help? shelbygt500buddy	Tue 09 June 2009 17:48 by shelbygt500buddy	8	9,907
Mixing different drives on the same controller shelbygt500buddy	Mon 15 June 2009 21:55 by Richards	5	7,827
dual motor on Y axis wiring ? shikha829	Mon 28 January 2013 20:07 by javeria	8	17,052
Cheaper drives SLINK	Wed 30 November 2011 02:33 by aniljangra	13	18,295
Cooling the Drives - Heatsinking and airflow soulvoid	Tue 10 November 2009 17:49 by riesvantwisk	19	24,693
Stepper motor & Driver from Oriental motor steven29	Sun 17 May 2015 11:20 by Richards	17	29,705
Inexpensive 3-axis driver boards Supertechster	Wed 10 March 2010 09:04 by rayditutto	15	17,477
Motor Not Locking Up on Power Up Surfcnc	Wed 14 November 2012 03:30 by Surfcnc	7	12,183
Universal Stepper Controller Ticapix	Tue 25 August 2009 20:41 by Gerald D	1	7,156
Gecko 201X Adjust Screw tnarch	Wed 23 March 2011 09:11 by MetalHead	2	9,614
New Gecko Faulting - RED LED tnarch	Thu 18 October 2012 23:56 by KenC	7	12,109
Need advice on stepper motor kit toad	Mon 10 May 2010 10:02 by toad	7	12,068
5 phase stepper motor. unns_boy	Mon 12 September 2011 16:58 by PEU	3	9,727
massmind diy stepper drivers userandrew	Fri 27 February 2015 17:52 by userandrew	6	12,087
Nema 34 set at 6000 velocity stops rotating viz	Sun 21 October 2012 02:49 by viz	20	24,123
gecko 210 WOODCHUCKMAN	Sat 21 February 2009 13:13 by WOODCHUCKMAN	3	7,238

Page 2 of 2

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 19:42.