701. Motor Drives - MechMate CNC Router Forum

		MechMate CNC Router Forum > Electrical & Electronic
701. Motor Drives

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 1 of 2

Threads in Forum : 701. Motor Drives

Forum Tools

Search this Forum

Thread / Thread Starter	Last Post	Replies	Views
Differences between G201, G202 and G203 stepper drives from Geckodrive ( 1 2) Gerald_D	Tue 03 April 2012 11:06 by darren salyer	59	78,251
Using the Gecko G540 drive a MechMate ( 1 2) stefanv	Sat 07 May 2011 03:45 by MAC2009	42	68,453
Geckodrives (California USA) ( 1 2 3 ... Last Page) Gerald_D	Fri 09 July 2010 12:20 by renraku	148	165,270

Spindle Frequency? lukebarber	Sat 23 March 2019 18:36 by lonestaral	2	24,858
Huanyang bit the dust, replaced with Lenze, question about parameters... Diplocaulus	Mon 28 January 2019 14:18 by danilom	1	6,911
Spindle won't stop spinning at program end or "Stop" engaged. Diplocaulus	Wed 26 December 2018 19:56 by ger21	5	11,409
Setting up a Huanyang HY02D223B VFD Jayson	Fri 02 November 2018 07:25 by ifffff	20	43,775
Buck Boost Transformer 380V 240V 3phase lukebarber	Fri 24 August 2018 19:15 by MetalHead	1	7,039
Gecko 203v - Blown fuse beckj	Sun 24 December 2017 09:05 by Kornerking	5	17,427
Read from Multiple Coils lukebarber	Thu 02 March 2017 12:04 by danilom	1	8,904
half-coil wiring of KL34H280-45-8A buddyLumen	Wed 01 June 2016 19:19 by buddyLumen	2	10,047
Stepper motor & Driver from Oriental motor steven29	Sun 17 May 2015 11:20 by Richards	17	29,489
massmind diy stepper drivers userandrew	Fri 27 February 2015 17:52 by userandrew	6	11,985
Geckodrive announced the GM215 stepper motor drive Richards	Sun 18 January 2015 10:21 by Robert M	1	7,681
Use Arduino Uno to test stepper drivers and stepper motors Richards	Sat 13 December 2014 11:12 by Richards	0	7,501
Gecko 203v intermittent fault paul60	Fri 12 September 2014 16:54 by smreish	17	26,044
Suspect gecko G 203V problem paul60	Thu 03 October 2013 09:19 by Richards	5	11,368
How much voltage do I really need? Richards	Thu 18 July 2013 17:54 by Richards	29	32,828
How to calculate resistor needed for gecko drives Richards	Wed 15 May 2013 08:52 by smreish	8	14,478
110 volt stepper driver...no need for PS? IMMark	Tue 19 February 2013 23:39 by Surfcnc	4	10,600
dual motor on Y axis wiring ? shikha829	Mon 28 January 2013 20:07 by javeria	8	16,948
open source drives g540 equivalent lolailando	Thu 10 January 2013 06:02 by darren salyer	4	9,629
Motor Not Locking Up on Power Up Surfcnc	Wed 14 November 2012 03:30 by Surfcnc	7	12,082
Would a size 23 motor work? Richards	Thu 08 November 2012 09:12 by Richards	3	10,172
Ruminations on production and stepper motors Richards	Tue 23 October 2012 06:31 by bradm	8	12,003
Nema 34 set at 6000 velocity stops rotating viz	Sun 21 October 2012 02:49 by viz	20	24,002
New Gecko Faulting - RED LED tnarch	Thu 18 October 2012 23:56 by KenC	7	12,018
Yasakawa V100 VFD Kobus_Joubert	Mon 16 January 2012 08:34 by Kobus_Joubert	12	15,143
Cheaper drives SLINK	Wed 30 November 2011 02:33 by aniljangra	13	18,220
5 phase stepper motor. unns_boy	Mon 12 September 2011 16:58 by PEU	3	9,647
Selecting resistors for Gecko drive Rusty Nuts	Mon 29 August 2011 19:49 by smreish	9	12,089
Servos for gecko drives. agfmaquinas	Thu 24 March 2011 15:45 by Jason Marsha	5	12,570
Gecko 201X Adjust Screw tnarch	Wed 23 March 2011 09:11 by MetalHead	2	9,531
Complete manual for Chinese VFD chrisd7306	Sat 20 November 2010 12:11 by Drad98_98	6	12,154
parallel port with mach3, or USB with usbcnc? cnc'tje	Fri 22 October 2010 09:56 by cnc'tje	12	21,384
Question about stepper drives and motor direction DTGuitars	Mon 18 October 2010 09:38 by bradm	13	20,442
Using steel control box as the heat sink G540 jwt	Mon 11 October 2010 09:22 by bradm	3	9,000
Andeli inverter english translation manual DenisCasserly	Fri 24 September 2010 17:35 by DenisCasserly	0	7,041
QJ8060 Drive from CW-Motors Francois	Tue 14 September 2010 12:31 by Francois	13	19,971
how to assign gecko driver to motors? renraku	Sun 12 September 2010 15:48 by Red_boards	3	9,480
One system controlling two tables? Mountaincraft	Fri 10 September 2010 18:27 by smreish	4	17,243
Dead Gecko's in S.Africa - a collection point for bulk return for repair Gerald D	Fri 09 July 2010 12:21 by Kobus_Joubert	8	13,645
digital stepping driver KenC	Sun 20 June 2010 10:20 by fanefane	7	14,840

Page 1 of 2

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 22:43.