Troubleshooting - Page 3 - MechMate CNC Router Forum

		MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance
Troubleshooting

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 3 of 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Cannot get good jog speeds - first thought PS voltage too low, then current error kwang90020	Tue 17 March 2009 14:28 by Gerald D	11	10,770
Loosing steps - noise interference problems MariusL	Sun 15 March 2009 06:34 by MariusL	14	11,834
One stepper motor does not change direction - drive needs reset waynec	Mon 16 February 2009 10:22 by waynec	13	14,217
Circles are not cut round - loose pinion gears sailfl	Sun 15 February 2009 18:19 by bradyaero	21	18,144
Lurching at Reset - interference from spindle VFD waynec	Thu 05 February 2009 18:00 by bradm	12	13,175
Shudder along X Axis - unresolved ( 1 2) sailfl	Sun 28 December 2008 15:32 by sailfl	30	21,342
Toggling inputs - faulty Campbell BoB Alan_c	Mon 08 December 2008 11:30 by Alan_c	15	15,949
One axis looses steps when going fast under load - change accel setting Greg J	Sun 07 December 2008 22:55 by Gerald D	10	10,496
Steps getting lost - poor quality parallel port cable javeria	Wed 03 December 2008 07:35 by javeria	5	6,452
One of the four motors not running properly - faulty Geckodrive 203V cncb	Sat 08 November 2008 08:46 by cncb	8	11,108
Problems with cooling fan.. - impeller touched the mounting plate cncb	Tue 04 November 2008 05:47 by cncb	17	12,308
Motors won't turn after the setting up - PMDX-122 jumpers incorrect lunaj76	Fri 31 October 2008 05:20 by J.R. Hatcher	13	10,683
Some files don't cut smoothly - Mach's interpret. of G-Code from various CAM programs ( 1 2) Greg J	Sat 25 October 2008 15:52 by Gerald D	30	21,183
Runs out of steam? Machine freezes during cutting - controlling PC's performance liaoh75	Thu 23 October 2008 23:34 by liaoh75	11	11,910
Cannot get motor to turn - Mach Ports & Pins setup kalimero	Tue 06 May 2008 10:50 by Greg J	18	21,754
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault ( 1 2) Daya	Mon 21 April 2008 02:05 by Glenn D	45	38,400
Machine cuts out after cutting for a while - Loose wire on E-stop circuit Hugo Carradini	Mon 31 March 2008 13:18 by Hugo Carradini	8	8,500
Getting comms between PC and PMDX-122 - Finding the correct port address ekdenton	Wed 26 March 2008 12:14 by ekdenton	2	5,202
One motor goes wrong way - How to reverse its direction grandpi	Sun 17 February 2008 23:03 by Gerald D	2	5,662
Machine locks up while travelling at high speed - Tuning the motor speeds and accels Doug_Ford	Sun 03 February 2008 22:55 by Gerald D	3	6,265
Glitches in cut paths (rounded corners) - Using the Constant Velocity mode of Mach J.R. Hatcher	Mon 28 January 2008 06:22 by J.R. Hatcher	3	5,350
System stops, as if the E-stop has been pushed? - Change De-Bounce setting in Mach Gerald D	Thu 24 January 2008 18:51 by smreish	4	5,658
No 5V supply out of PC - Polarity reversed J.R. Hatcher	Thu 24 January 2008 17:50 by J.R. Hatcher	1	4,073
Contactor does nothing when powered? - Correct terminals for coil Doug_Ford	Sun 11 November 2007 19:23 by Doug_Ford	11	11,868
Upgraded Mach, now the motors won't turn - Different ports/pins for later Mach Hugo Carradini	Thu 25 October 2007 12:45 by Hugo Carradini	19	16,670
Machine runs far too slow (or fast) and the wrong distances - Confusing inch/mm 's Hugo Carradini	Tue 25 September 2007 10:44 by Hugo Carradini	2	6,105
Jerky movement of the gantries - Limit Overides activated in Mach ( 1 2) fabrica	Tue 23 January 2007 10:39 by fabrica	31	18,954
Motors do not move after initial setting up - Mach setups fabrica	Fri 19 January 2007 02:04 by fabrica	17	9,932

Page 3 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 23:47.