Troubleshooting - Page 2 - MechMate CNC Router Forum

		MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance
Troubleshooting

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 2 of 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Imperial vs metric ... silverdog	Mon 25 July 2011 11:10 by isladelobos	17	19,050
Strange movements - bad power supply to BOB tnarch	Fri 25 March 2011 20:37 by Surfcnc	26	25,315
Matty Zee Mach 3 Pluggin ( 1 2) AuS MaDDoG	Wed 19 January 2011 05:50 by Surfcnc	35	41,181
Hitachi SJ200 and ModBus Control Problems skippy	Wed 19 January 2011 05:03 by AuS MaDDoG	3	9,247
Gecko Problems after Computer Crash agfmaquinas	Mon 13 December 2010 18:00 by bradm	1	6,557
3d Mold divot issue - SOLVED - Loose screw holding pinion gear ( 1 2) salewis	Tue 23 November 2010 12:36 by salewis	41	33,384
Spindle RF noise makes y car & z axis move smreish	Wed 20 October 2010 10:03 by smreish	22	23,170
Mach3 to HY series VFD on/off control AJWConstruction	Tue 19 October 2010 19:53 by Kenrbass	2	5,916
Chatter Marks on Cutting rotorzoomer	Mon 23 August 2010 19:15 by smreish	10	12,422
Ghost in the machine ?... Router creating its own G code Blue eleven	Mon 02 August 2010 23:12 by Blue eleven	22	19,997
Motors Will Not Turn - Step & Direction wires crossed by mistake toad	Sun 01 August 2010 11:49 by JamesJ	17	12,472
Slight step over on second/third pass Dan Sj0	Sat 10 July 2010 06:55 by Alan_c	2	6,261
Z dropping suddenly - computer response is slower javeria	Fri 23 April 2010 12:12 by javeria	14	11,349
Power Contactor Not Working Regnar	Sat 10 April 2010 13:38 by bradm	28	23,179
Loosing Steps - underpowered ? Claudiu	Thu 18 February 2010 14:53 by Richards	24	18,591
Proper Homing javeria	Sun 24 January 2010 06:28 by sailfl	25	18,542
Rough Cut on Diagonal ( 1 2 3 ... Last Page) sailfl	Sat 23 January 2010 09:22 by isladelobos	191	109,019
Motors are weak and run cool - setting up a "Leadshine" drive lumberjack_jeff	Mon 04 January 2010 08:08 by lumberjack_jeff	7	8,759
shutdown problem paul60	Wed 30 December 2009 05:42 by paul60	13	13,493
Trouble Shooting Standards MetalHead	Sat 14 November 2009 17:32 by MetalHead	1	4,662
Backlash compensation lumberjack_jeff	Sat 14 November 2009 08:30 by Gerald D	10	11,506
"Weak" z-axis won't plunge cutter - router turned off ( 1 2) javeria	Sat 14 November 2009 08:10 by Gerald D	30	21,522
Motors loosing steps - Breakout board not suitable mgandy02	Mon 02 November 2009 11:01 by mgandy02	17	15,533
All motors run fine then start chattering and loosing steps - interrupt in the PC KevinL	Wed 14 October 2009 22:11 by Gerald D	24	20,033
Gecko 203v red and green light all the time mordalez	Fri 25 September 2009 10:35 by mordalez	2	6,153
Inconsistent accuracy - loose pinion gear bfauska	Sat 05 September 2009 10:05 by Gerald D	11	12,052
Cutting speed becomes irregular - computer not matched properly martin77pl	Wed 02 September 2009 12:55 by martin77pl	5	6,156
Table not cutting Y square to X gorantec	Sat 29 August 2009 13:49 by jhiggins7	5	7,315
Parallel cable does not work - all the cores are not present martin77pl	Thu 30 July 2009 10:14 by javeria	9	9,406
Motors do not turn - Ports & Pins setting for charge pump ( 1 2) Conrado_Navarro	Fri 10 July 2009 23:08 by Gerald D	37	25,186
Racks not square to Pinon gears - C-channel tops not flat, twisting rail down sailfl	Wed 17 June 2009 19:11 by smreish	13	11,025
Cutting out_of_round circles - loose V-rollers on Z-slide javeria	Wed 17 June 2009 06:15 by javeria	22	19,993
Motors move too slowly - unresolved Gato Richy	Thu 21 May 2009 00:04 by Gerald D	10	9,476
Fault lights on some Geckos, motors do not engage - wiring quality Gato Richy	Tue 19 May 2009 16:00 by Gato Richy	14	13,461
RCD / Earth Leakage trips when switching off - fan wiring Gerald D	Tue 19 May 2009 07:27 by Gerald D	0	4,629
Stepper motor refuses to turn - Wiring & jumper errors ( 1 2) Gato Richy	Fri 01 May 2009 00:56 by Gerald D	31	32,405
Creeping z-axis - a cable screen was grounded at both ends Barrie	Wed 29 April 2009 00:08 by Gerald D	4	6,554
Motors do not turn properly - poor quality wiring used for testing martin77pl	Tue 31 March 2009 12:36 by martin77pl	8	7,833
Milwaukee Router weirdness - SSR (solid state relay) not suitable jeffh	Thu 26 March 2009 13:03 by jeffh	26	23,238
Moves at different speeds for different directions - feed rates incorrectly defined Kobus_Joubert	Sun 22 March 2009 06:16 by Gerald D	16	14,113

Page 2 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 07:22.