Troubleshooting - Page 3 - MechMate CNC Router Forum

		MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance
Troubleshooting

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 3 of 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Moves at different speeds for different directions - feed rates incorrectly defined Kobus_Joubert	Sun 22 March 2009 05:16 by Gerald D	16	26,414
Cannot get good jog speeds - first thought PS voltage too low, then current error kwang90020	Tue 17 March 2009 13:28 by Gerald D	11	21,162
Loosing steps - noise interference problems MariusL	Sun 15 March 2009 05:34 by MariusL	14	25,625
One stepper motor does not change direction - drive needs reset waynec	Mon 16 February 2009 09:22 by waynec	13	24,255
Circles are not cut round - loose pinion gears sailfl	Sun 15 February 2009 17:19 by bradyaero	21	33,793
Lurching at Reset - interference from spindle VFD waynec	Thu 05 February 2009 17:00 by bradm	12	24,452
Shudder along X Axis - unresolved ( 1 2) sailfl	Sun 28 December 2008 14:32 by sailfl	30	42,252
Toggling inputs - faulty Campbell BoB Alan_c	Mon 08 December 2008 10:30 by Alan_c	15	29,194
One axis looses steps when going fast under load - change accel setting Greg J	Sun 07 December 2008 21:55 by Gerald D	10	19,174
Steps getting lost - poor quality parallel port cable javeria	Wed 03 December 2008 06:35 by javeria	5	11,896
One of the four motors not running properly - faulty Geckodrive 203V cncb	Sat 08 November 2008 07:46 by cncb	8	21,756
Problems with cooling fan.. - impeller touched the mounting plate cncb	Tue 04 November 2008 04:47 by cncb	17	19,738
Motors won't turn after the setting up - PMDX-122 jumpers incorrect lunaj76	Fri 31 October 2008 04:20 by J.R. Hatcher	13	18,144
Some files don't cut smoothly - Mach's interpret. of G-Code from various CAM programs ( 1 2) Greg J	Sat 25 October 2008 14:52 by Gerald D	30	39,498
Runs out of steam? Machine freezes during cutting - controlling PC's performance liaoh75	Thu 23 October 2008 22:34 by liaoh75	11	36,641
Cannot get motor to turn - Mach Ports & Pins setup kalimero	Tue 06 May 2008 09:50 by Greg J	18	40,779
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault ( 1 2) Daya	Mon 21 April 2008 01:05 by Glenn D	45	93,005
Machine cuts out after cutting for a while - Loose wire on E-stop circuit Hugo Carradini	Mon 31 March 2008 12:18 by Hugo Carradini	8	19,355
Getting comms between PC and PMDX-122 - Finding the correct port address ekdenton	Wed 26 March 2008 11:14 by ekdenton	2	10,580
One motor goes wrong way - How to reverse its direction grandpi	Sun 17 February 2008 22:03 by Gerald D	2	13,348
Machine locks up while travelling at high speed - Tuning the motor speeds and accels Doug_Ford	Sun 03 February 2008 21:55 by Gerald D	3	14,263
Glitches in cut paths (rounded corners) - Using the Constant Velocity mode of Mach J.R. Hatcher	Mon 28 January 2008 05:22 by J.R. Hatcher	3	10,861
System stops, as if the E-stop has been pushed? - Change De-Bounce setting in Mach Gerald D	Thu 24 January 2008 17:51 by smreish	4	11,053
No 5V supply out of PC - Polarity reversed J.R. Hatcher	Thu 24 January 2008 16:50 by J.R. Hatcher	1	8,086
Contactor does nothing when powered? - Correct terminals for coil Doug_Ford	Sun 11 November 2007 18:23 by Doug_Ford	11	24,792
Upgraded Mach, now the motors won't turn - Different ports/pins for later Mach Hugo Carradini	Thu 25 October 2007 11:45 by Hugo Carradini	19	32,851
Machine runs far too slow (or fast) and the wrong distances - Confusing inch/mm 's Hugo Carradini	Tue 25 September 2007 09:44 by Hugo Carradini	2	14,792
Jerky movement of the gantries - Limit Overides activated in Mach ( 1 2) fabrica	Tue 23 January 2007 09:39 by fabrica	31	39,309
Motors do not move after initial setting up - Mach setups fabrica	Fri 19 January 2007 01:04 by fabrica	17	17,455

Page 3 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 19:55.