Troubleshooting - Page 2 - MechMate CNC Router Forum

		MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance
Troubleshooting

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 2 of 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Need help with jog speed in Mach3 motor tuning !!! ( 1 2) rival	Sat 03 September 2011 05:03 by Surfcnc	45	83,050
Imperial vs metric ... silverdog	Mon 25 July 2011 10:10 by isladelobos	17	28,087
Strange movements - bad power supply to BOB tnarch	Fri 25 March 2011 19:37 by Surfcnc	26	41,092
Matty Zee Mach 3 Pluggin ( 1 2) AuS MaDDoG	Wed 19 January 2011 04:50 by Surfcnc	35	67,205
Hitachi SJ200 and ModBus Control Problems skippy	Wed 19 January 2011 04:03 by AuS MaDDoG	3	17,056
Gecko Problems after Computer Crash agfmaquinas	Mon 13 December 2010 17:00 by bradm	1	11,838
3d Mold divot issue - SOLVED - Loose screw holding pinion gear ( 1 2) salewis	Tue 23 November 2010 11:36 by salewis	41	65,965
Spindle RF noise makes y car & z axis move smreish	Wed 20 October 2010 09:03 by smreish	22	36,614
Mach3 to HY series VFD on/off control AJWConstruction	Tue 19 October 2010 18:53 by Kenrbass	2	11,572
Chatter Marks on Cutting rotorzoomer	Mon 23 August 2010 18:15 by smreish	10	21,080
Ghost in the machine ?... Router creating its own G code Blue eleven	Mon 02 August 2010 22:12 by Blue eleven	22	33,868
Motors Will Not Turn - Step & Direction wires crossed by mistake toad	Sun 01 August 2010 10:49 by JamesJ	17	20,519
Slight step over on second/third pass Dan Sj0	Sat 10 July 2010 05:55 by Alan_c	2	11,921
Z dropping suddenly - computer response is slower javeria	Fri 23 April 2010 11:12 by javeria	14	18,724
Power Contactor Not Working Regnar	Sat 10 April 2010 12:38 by bradm	28	48,288
Loosing Steps - underpowered ? Claudiu	Thu 18 February 2010 13:53 by Richards	24	31,612
Proper Homing javeria	Sun 24 January 2010 05:28 by sailfl	25	30,254
Rough Cut on Diagonal ( 1 2 3 ... Last Page) sailfl	Sat 23 January 2010 08:22 by isladelobos	191	178,358
Motors are weak and run cool - setting up a "Leadshine" drive lumberjack_jeff	Mon 04 January 2010 07:08 by lumberjack_jeff	7	15,805
shutdown problem paul60	Wed 30 December 2009 04:42 by paul60	13	53,711
Trouble Shooting Standards MetalHead	Sat 14 November 2009 16:32 by MetalHead	1	9,464
Backlash compensation lumberjack_jeff	Sat 14 November 2009 07:30 by Gerald D	10	20,770
"Weak" z-axis won't plunge cutter - router turned off ( 1 2) javeria	Sat 14 November 2009 07:10 by Gerald D	30	42,243
Motors loosing steps - Breakout board not suitable mgandy02	Mon 02 November 2009 10:01 by mgandy02	17	26,663
All motors run fine then start chattering and loosing steps - interrupt in the PC KevinL	Wed 14 October 2009 21:11 by Gerald D	24	33,042
Gecko 203v red and green light all the time mordalez	Fri 25 September 2009 09:35 by mordalez	2	13,282
Inconsistent accuracy - loose pinion gear bfauska	Sat 05 September 2009 09:05 by Gerald D	11	54,653
Cutting speed becomes irregular - computer not matched properly martin77pl	Wed 02 September 2009 11:55 by martin77pl	5	11,511
Table not cutting Y square to X gorantec	Sat 29 August 2009 12:49 by jhiggins7	5	13,551
Parallel cable does not work - all the cores are not present martin77pl	Thu 30 July 2009 09:14 by javeria	9	15,042
Motors do not turn - Ports & Pins setting for charge pump ( 1 2) Conrado_Navarro	Fri 10 July 2009 22:08 by Gerald D	37	46,931
Racks not square to Pinon gears - C-channel tops not flat, twisting rail down sailfl	Wed 17 June 2009 18:11 by smreish	13	19,618
Cutting out_of_round circles - loose V-rollers on Z-slide javeria	Wed 17 June 2009 05:15 by javeria	22	69,161
Motors move too slowly - unresolved Gato Richy	Wed 20 May 2009 23:04 by Gerald D	10	16,393
Fault lights on some Geckos, motors do not engage - wiring quality Gato Richy	Tue 19 May 2009 15:00 by Gato Richy	14	24,544
RCD / Earth Leakage trips when switching off - fan wiring Gerald D	Tue 19 May 2009 06:27 by Gerald D	0	9,580
Stepper motor refuses to turn - Wiring & jumper errors ( 1 2) Gato Richy	Thu 30 April 2009 23:56 by Gerald D	31	72,097
Creeping z-axis - a cable screen was grounded at both ends Barrie	Tue 28 April 2009 23:08 by Gerald D	4	12,433
Motors do not turn properly - poor quality wiring used for testing martin77pl	Tue 31 March 2009 11:36 by martin77pl	8	14,117
Milwaukee Router weirdness - SSR (solid state relay) not suitable jeffh	Thu 26 March 2009 12:03 by jeffh	26	38,986

Page 2 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 19:55.