Troubleshooting - Page 2 - MechMate CNC Router Forum

		MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance
Troubleshooting

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 2 of 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Imperial vs metric ... silverdog	Mon 25 July 2011 10:10 by isladelobos	17	19,972
Strange movements - bad power supply to BOB tnarch	Fri 25 March 2011 19:37 by Surfcnc	26	26,854
Matty Zee Mach 3 Pluggin ( 1 2) AuS MaDDoG	Wed 19 January 2011 04:50 by Surfcnc	35	43,608
Hitachi SJ200 and ModBus Control Problems skippy	Wed 19 January 2011 04:03 by AuS MaDDoG	3	9,741
Gecko Problems after Computer Crash agfmaquinas	Mon 13 December 2010 17:00 by bradm	1	6,883
3d Mold divot issue - SOLVED - Loose screw holding pinion gear ( 1 2) salewis	Tue 23 November 2010 11:36 by salewis	41	37,158
Spindle RF noise makes y car & z axis move smreish	Wed 20 October 2010 09:03 by smreish	22	24,358
Mach3 to HY series VFD on/off control AJWConstruction	Tue 19 October 2010 18:53 by Kenrbass	2	6,304
Chatter Marks on Cutting rotorzoomer	Mon 23 August 2010 18:15 by smreish	10	13,258
Ghost in the machine ?... Router creating its own G code Blue eleven	Mon 02 August 2010 22:12 by Blue eleven	22	21,776
Motors Will Not Turn - Step & Direction wires crossed by mistake toad	Sun 01 August 2010 10:49 by JamesJ	17	13,371
Slight step over on second/third pass Dan Sj0	Sat 10 July 2010 05:55 by Alan_c	2	6,620
Z dropping suddenly - computer response is slower javeria	Fri 23 April 2010 11:12 by javeria	14	12,215
Power Contactor Not Working Regnar	Sat 10 April 2010 12:38 by bradm	28	27,631
Loosing Steps - underpowered ? Claudiu	Thu 18 February 2010 13:53 by Richards	24	20,165
Proper Homing javeria	Sun 24 January 2010 05:28 by sailfl	25	20,275
Rough Cut on Diagonal ( 1 2 3 ... Last Page) sailfl	Sat 23 January 2010 08:22 by isladelobos	191	123,009
Motors are weak and run cool - setting up a "Leadshine" drive lumberjack_jeff	Mon 04 January 2010 07:08 by lumberjack_jeff	7	9,434
shutdown problem paul60	Wed 30 December 2009 04:42 by paul60	13	14,486
Trouble Shooting Standards MetalHead	Sat 14 November 2009 16:32 by MetalHead	1	4,910
Backlash compensation lumberjack_jeff	Sat 14 November 2009 07:30 by Gerald D	10	12,539
"Weak" z-axis won't plunge cutter - router turned off ( 1 2) javeria	Sat 14 November 2009 07:10 by Gerald D	30	23,074
Motors loosing steps - Breakout board not suitable mgandy02	Mon 02 November 2009 10:01 by mgandy02	17	16,655
All motors run fine then start chattering and loosing steps - interrupt in the PC KevinL	Wed 14 October 2009 21:11 by Gerald D	24	21,410
Gecko 203v red and green light all the time mordalez	Fri 25 September 2009 09:35 by mordalez	2	6,539
Inconsistent accuracy - loose pinion gear bfauska	Sat 05 September 2009 09:05 by Gerald D	11	12,925
Cutting speed becomes irregular - computer not matched properly martin77pl	Wed 02 September 2009 11:55 by martin77pl	5	6,592
Table not cutting Y square to X gorantec	Sat 29 August 2009 12:49 by jhiggins7	5	7,756
Parallel cable does not work - all the cores are not present martin77pl	Thu 30 July 2009 09:14 by javeria	9	9,946
Motors do not turn - Ports & Pins setting for charge pump ( 1 2) Conrado_Navarro	Fri 10 July 2009 22:08 by Gerald D	37	27,080
Racks not square to Pinon gears - C-channel tops not flat, twisting rail down sailfl	Wed 17 June 2009 18:11 by smreish	13	11,848
Cutting out_of_round circles - loose V-rollers on Z-slide javeria	Wed 17 June 2009 05:15 by javeria	22	21,304
Motors move too slowly - unresolved Gato Richy	Wed 20 May 2009 23:04 by Gerald D	10	10,068
Fault lights on some Geckos, motors do not engage - wiring quality Gato Richy	Tue 19 May 2009 15:00 by Gato Richy	14	14,420
RCD / Earth Leakage trips when switching off - fan wiring Gerald D	Tue 19 May 2009 06:27 by Gerald D	0	4,890
Stepper motor refuses to turn - Wiring & jumper errors ( 1 2) Gato Richy	Thu 30 April 2009 23:56 by Gerald D	31	35,508
Creeping z-axis - a cable screen was grounded at both ends Barrie	Tue 28 April 2009 23:08 by Gerald D	4	6,970
Motors do not turn properly - poor quality wiring used for testing martin77pl	Tue 31 March 2009 11:36 by martin77pl	8	8,401
Milwaukee Router weirdness - SSR (solid state relay) not suitable jeffh	Thu 26 March 2009 12:03 by jeffh	26	24,692
Moves at different speeds for different directions - feed rates incorrectly defined Kobus_Joubert	Sun 22 March 2009 05:16 by Gerald D	16	15,298

Page 2 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 16:46.