One more MechMate starting - North Carolina, USA

[Bernhard]

Hello,
after lurking for quite a while and dilligently reading most every thread, it's time to build my own MM.
I had started to build a router from scratch before I found this site. Since I wasn't very far along, I thought it to be wise to quit and follow a workable and proven disign. This site and the design is by far superior to everything else I found on the web. Most other designs are either hobby outfit or unworkable.
Most materials acquired sofar (stepper, drives, enclosure, etc) will work fine with the MM. So other than some steel, not much is lost.

So, just placed the order for the steel to be picked up next week. Luckily a friend of mine works at one of the local steel warehouses, so I get the steel at a very competitive cost.

This project will go a bit slow, since I am still building my house at the same time. BUT the important thing is that my shop is finished and pretty well equiped, just missing the CNC router.

Cheers,
Bernhard

[cbboatworks]

Welcome Bernhard


What part of NC are you from?

After looking at your profile I see where from. I am from Durham. I made the move to Carolina Beach about 8 yrs ago, I was up your way a few weeks ago picking up Metal at a Salvage yard on Cheek Rd. If you need it they more than likely have it. so take a ride out that way and take a look.I picked up my control box from them for around $12.00. they sell Aluminum stock for $1.40 pound also they sell steel for $.30 a pound. let me know if I can help with anything. Good luck with you build.

cbboatworks@aol.com

[Bernhard]

Welcome Bernhard


What part of NC are you from?

After looking at your profile I see where from. I am from Durham. I made the move to Carolina Beach about 8 yrs ago, I was up your way a few weeks ago picking up Metal at a Salvage yard on Cheek Rd. If you need it they more than likely have it. so take a ride out that way and take a look.I picked up my control box from them for around $12.00. they sell Aluminum stock for $1.40 pound also they sell steel for $.30 a pound. let me know if I can help with anything. Good luck with you build.

cbboatworks@aol.com

Gene,

I actually live out in the country, about 25 miles outside Durham, but my day job is in Durham.
And yes, I just found out about the Cheek Road salvage place. I stopped by last week on my way home from work, but it was about to close. The owner let me look around until he locked up. Need to stop by next week and load up!

BTW, have you built or are you building a MM? And if so can I take a peek at it?

Cheers,

Bernhard

[J.R. Hatcher]

Bernhard, I have my MM well under way so if your in the Wilmington, NC area you would be welcome to stop by and see it. My tele # is 9106869850. J.R.

[Bernhard]

Bernhard, I have my MM well under way so if your in the Wilmington, NC area you would be welcome to stop by and see it. My tele # is 9106869850. J.R.

JR,
Thank you for your offer.. I will take you up on it. I have been following your progress; you do excellent work!

Havn't had a chance to work much on my router, but have acquired more parts (Gecko 203V, PS, igus chains etc).

Cheers,
Bernhard

[cbboatworks]

bernhard

I was over at Jr's on Thursday and his machine is absolutely amazing. if you get a Chance drive to Wilmington take him up on the offer. after seeing his machine again I am back and ready to start building.


Gene



JR,
Thank you for your offer.. I will take you up on it. I have been following your progress; you do excellent work!

Havn't had a chance to work much on my router, but have acquired more parts (Gecko 203V, PS, igus chains etc).

Cheers,
Bernhard