PDA

View Full Version : 701. Motor Drives

  1. Geckodrives (California USA)
  2. Delta Variable Frequency Drive VFDB series - (for the spindle motor)
  3. Centent (California, USA)
  4. Differences between G201, G202 and G203 stepper drives from Geckodrive
  5. Motionking (China)
  6. Motion Control Products Ltd (Bournemouth England)
  7. Cooling the Drives - Heatsinking and airflow
  8. Geckos on sale!!!!
  9. Heatsink compounds (thermal greases)
  10. Schematics/Circuit Diagram for 3 Axis Driver with Parallel Port Interphase
  11. Using the Gecko G540 drive a MechMate
  12. Do not purchase Vacuum application drives from Geckodrive
  13. cnc amazing world-could anybody help me?
  14. Gecko / Motor Tuning
  15. Servo motors
  16. Geckodrive's Yahoo forum - not meant for official support
  17. need 6A bipolar scheme
  18. "Gecko 540" vs. "PMDX-122 & Geckos 203V"
  19. gecko 210
  20. Spindle Collet
  21. Electrical Phase Type Compatible
  22. QJ8060 Drive from CW-Motors
  23. Programming Delta VFD's for spindle motors
  24. Setting up a Huanyang HY02D223B VFD
  25. Found a new type of driver could save some money please help?
  26. Mixing different drives on the same controller
  27. digital stepping driver
  28. RMS or PEAK
  29. Max power supply voltage for Gecko G540
  30. Universal Stepper Controller
  31. PMDX-122 & Geckos 203V Diagram ???
  32. bipolar (parallel) connection stepper's
  33. Resistors for G504 and wiring for PK296A2A-SG7.2 motors (unipolar)
  34. Sounds different bipolar unipolar
  35. 2.2 kw HF spindle drive Vancouver Canada
  36. Newbie needs help with figuring out drive configurations (slaved drive for x-axis)
  37. axis X one stepper motor
  38. Finding a VFD to suit a 3kW spindle in Denmark
  39. Inexpensive 3-axis driver boards
  40. Need advice on stepper motor kit
  41. parallel port with mach3, or USB with usbcnc?
  42. running stepper motor with printer data pcb board
  43. Dead Gecko's in S.Africa - a collection point for bulk return for repair
  44. How to calculate resistor needed for gecko drives
  45. how to assign gecko driver to motors?
  46. One system controlling two tables?
  47. Andeli inverter english translation manual
  48. Complete manual for Chinese VFD
  49. Using steel control box as the heat sink G540
  50. Question about stepper drives and motor direction
  51. How much voltage do I really need?
  52. Servos for gecko drives.
  53. Gecko 201X Adjust Screw
  54. New Gecko Faulting - RED LED
  55. Selecting resistors for Gecko drive
  56. 5 phase stepper motor.
  57. Gecko 203v - Blown fuse
  58. Cheaper drives
  59. Yasakawa V100 VFD
  60. Nema 34 set at 6000 velocity stops rotating
  61. Ruminations on production and stepper motors
  62. Would a size 23 motor work?
  63. Motor Not Locking Up on Power Up
  64. open source drives g540 equivalent
  65. dual motor on Y axis wiring ?
  66. 110 volt stepper driver...no need for PS?
  67. Suspect gecko G 203V problem
  68. Gecko 203v intermittent fault
  69. Use Arduino Uno to test stepper drivers and stepper motors
  70. Geckodrive announced the GM215 stepper motor drive
  71. massmind diy stepper drivers
  72. Stepper motor & Driver from Oriental motor
  73. half-coil wiring of KL34H280-45-8A
  74. Read from Multiple Coils
  75. Buck Boost Transformer 380V 240V 3phase
  76. Spindle won't stop spinning at program end or "Stop" engaged.
  77. Huanyang bit the dust, replaced with Lenze, question about parameters...
  78. Spindle Frequency?